I guess the clocker used a cheap mileage tool that only corrected the BCM/dash without a engine option. I’ve gone into the engine ECU computer, all of the live data are shown here, just select the “Total Distance” option, then press “Show” button.Īs you can see, the total distance from manufacturer is 248345.61 miles. Let’s connect the scanner with OBD, and go through to live data directly. The mileage displayed on the dashboard is 154410 miles.
So I’m going to use an Autel MaxiSys scanner to diagnose it, like MS906, MS906BT, MS908S Pro will work.
This is a 2014 Ford vehicle brought from one customer, which was believed to be false mileage on.
How to use BMW INPA software and cable K+DCAN
How to install TIS2000 for GM Tech 2 scanner
Install BMW INPA on WinXP Win7 Win8 Win10įree Download BMW E-sys V3.22.5 v3.2.61 v3.2.71įree ECM Titanium 1.61 with 26000 drivers How to Install Toyota TIS Techstream 14.10.028
Users can check PSA odometer Help menu in OBDSTAR X300 DP Plus tablet as well. Types can be seen on the BSI module label, as shown below. According to the BSI module brand type, Valeo is generally F21, Continent is generally F19, and JOHNSON CONTROLS is generally F12… īSI menu is based on types, such as “CONTINENTAL BSI-Q0X”, where CONTINENTAL is the BSI brand name, Q0X is the BSI type, X stands for any number 0-9, the device can automatically recognize, if not, the types are not supported. Note: The position of the fuses may vary depending on years and models. The instrument fuse is on the BSI, and the BSI position is generally below the steering wheel, as shown below. After that, enter the reading mileage, confirm the mileage to be adjusted, and then install the instrument fuse The value is consistent with the instrument. After the adjustment is successful, immediately unplug the instrument power supply fuse (as fast as possible, it is recommended to unplug the fuse before adjusting the instrument to check whether the instrument is powered off), and then adjust the BSI mileage through OBD. After that, enter the reading mileage, confirm the mileage to be adjusted, and then install the instrument įirst adjust the instrument mileage through OBD. After the adjustment is successful, immediately unplug the instrument (as fast as possible), and then adjust the BSI mileage through OBD.
The solution is as follows:įirst remove the adjustment, do not pull the plug, and then adjust the instrument mileage through OBD. If one of them is adjusted first, it will be synchronized by the data of another module and restored to the original mileage. For the mileage reset, it needs to adjust the instrument and BSI module at the same time.Before performing the adjustment, you must first read and save the instrument and BSI data (EEPROM and FLASH).During the mileage adjustment process, ensure that the power is sufficient and the voltage is stable.Do not turn off the ignition after completion!! Powerģ. Turn on the ignition and calibrate the BSI. Remove the instrument and use the programmer to calibrate itĢ. II.Steps of onty BSI supporting the OBD calibration:ġ. Reconnect the battery negative cable and complete Calibrate the BSI, and do not turn off the ignition after completion!! Power off the battery for 10 minutesĤ. Calibrate the instrument, and do not turn off the ignition after completionģ. I Both the instrument and BSI support OBD calibration steps:Ģ. Part 2: OBDSTAR PSA Dashboard and BSI mileage correction manual: OBDSTAR X300DP Plus and Odo Master Supports more PSA models than X300M BrandĬONTINENTAL SC667050+95256 CAN(BSI-Q0X-00) OBDSTAR supports following PSA odometer correction car list:Ĭontinental SC67050 + 95256 CAN (BSI-Q0X-00) OBDSTAR tools ( X300 DP Plus & Odomaster) PSA Peugeot Citroen DS odometer correction vehicle coverage and instructions.